Stains from hand creams from most fabrics come off during the traditional laundry.


Their cleaning always starts with the collection of excess cream. If you did not remove the stain dry, then wipe it with a cotton swab soaked in white spirit. You can also rub the stain with liquid detergent, then rinse thoroughly with warm water.

If the cream accidentally lands on the carpet, collect it gently, so as not to increase the stain. Sponge put on chemical stain agent for carpet cleaning, diluted according to the manufacturer. We wait until the stain is dry and vacuuming it. If the stain is still visible, then repeat the whole procedure again.

Glue stains cellulose is a common ailment of children of school age.


The soiled fabric glue should be soaked in cold water for half an hour. After this time, clean the stain with a solution of salmaniaku. The next step is washing clothes under a strong stream running, warm water. Then wash the fabric according to manufacturer's instructions with the addition of the enzyme powder.

You can also rub the stain with a cotton swab moistened with alcohol or white spirit and wash clothing in hot water and washing powder. After this treatment the stain is not gone.

Silk is left for a long time in the closet, under adverse conditions tend to overlap spots of moisture.


If spots appear on the white silk to gently sprinkle them with lemon juice and then washed. On a dark silk should disappear after washing. If, however, can still be seen then mix in equal parts water and vinegar and soak a cotton ball in it. Gently rub the cloth.

This should remove all stains. To avoid stains, please note that from time to air our clothes of silk fabrics. This is to prevent unsightly stains.

Spinach stains are not exclusively the domain of small children.


There are also adults. If the stain with spinach will settle on our clothes, then you should remove it as soon as possible. To this end, we wipe dirty place przekrojonym in half, raw potato.

Another way is to immediately WASH spots under running water and then soaking the stained cloth in warm water with detergent. After half an hour of soaking the fabric airing. The laundry can add a chemical stain remover. Stains on white fabrics can also wipe with oxygenated water.

Fecal stains should be removed as soon as they arise, otherwise it will be much harder.

We start from scrape layers of fabric stool. Then, dipping it in water and borax. After half an hour of lingerie and clothing remove and rinse in lukewarm water. The next step is to wash according to manufacturer's instructions with the addition of washing powder. The powder was the best by an enzyme. If the white fabric will remain yellow marks, then you can wipe it with a cotton swab soaked in hydrogen peroxide or bleach in the sun. Stains after such treatment will disappear.

If our clothes will be stained with carbon paper under the fabric then the primer layer of paper towels.

On the surface, been covering the stain with a cloth with carbon tetrachloride. We wait until the solvent evaporates. We make sure that the layer of towels were clean and, if necessary, change them. After drying the solvent wettable with water and rub the stain in her laundry detergent or other detergent.

Deny cloth and then rinse under running water, or wash the tradition. If a stain on the fabric ribbons formed, which do not work, then we are left with only putting it to the dry cleaners.

For bathtubs iron and enamelled, and acrylic enamels can be used for high gloss acrylic-based polyurethane resin, with a hardener. These enamels with unique physical and chemical properties.

Through the use of these shiny paint pigments have sensational shine and long-lasting color. Very well hidden surfaces and stick, fill cavities, form fitting hard shell. These enamels are suitable for bathtubs and toilets to renew, for sinks, wash basins, shower trays, ceramic tiles. Besides, it can also be used on other surfaces, ceramic, wood, laminate surfaces (boats, yachts, airplanes), stainless steel and aluminum, as well as to cover the plastic parts.

Paints are designed to cover the surface of the water line and below the waterline, internal and external. Before applying the enamel, the surface should be sanded, dry and free of grease. There is no need for sanding between coats, if the next ink layer is deposited in about 24 hours. As a maintenance coating, enamel can be applied to well-adherent coatings, formed on the basis of other two-component paints (polyurethane epoxydowych), or directly on the degreased surfaces raw.

The enamel should be applied by brush, roller or spray gun. The surface paint preferably at about 20 degrees C. This temperature is responsible for a good drying enamel. Drying time also depends on the humidity and density of the product. Painting should be done in a well ventilated rooms. Unpainted surfaces have to be covered, and then apply the enamel.
Author: Home Contractor Chicago & Residential Painting Dallas

Water and sewage systems are needed in every home, regardless of its nature. Domestic hot and cold water and central heating systems are generally water systems. They can be made of different materials, using different methods.
The basic element of any water system are tubes that most are 1.2 inches, or about 15mm in diameter. They allow you to bring water to the faucet, flushing, heaters and sinks. Water pipes that bring water to the other floors of the house or to some cisterns and batteries may be thicker and have up to 1 ¼ inches in diameter. On the other hand, drainage pipes of wash basins, sinks, washing machines, baths and toilets can range from 40 mm to 70 mm wide.

The pipes are connected together via a permanent joints and detachable. Among the distinguished permanent joints welded connections, crimp or-Press, glued, soldered and welded. Among the detachable connections, in turn, can replace the screw connections and fittings. It is worth noting that the releasable connection are easy to install and remove, but are less durable than permanent joints.
sewerage
Water systems can be made using different materials. At present, the most commonly used residential installation is plastic - less copper or steel. Among the materials which are the building blocks for water systems distinguished by its derivative PVC and CPVC (chlorinated polyvinyl chloride), polyethylene (PE), cross-linked polyethylene (PE-X), polypropylene (PP), polybutylene (PB) and the layered tube.
Sewage system in buildings is necessary for the discharge of waste water, but sewer is called both municipal sewage and contaminated water, or rain water and condensation. The house can be the total number of connected to the sewer system outside, but always at the same time it should be noted that it is running ogólnospławnym or separable. For ogólnospławnym both sewage runoff, as well as domestic and economic origin, are discharged one and the same pipe.
In turn, the separation system, household sewage is discharged by means of one pipe and the wastewater runoff with the second pipe. The advantage of this system is the ability to throw off rainwater sewage directly into rivers without causing pollution of surface waters. Unfortunately, the combined system enforces the use of wastewater, which in storms and heavy rainfall causes the municipal enterprises must pay the excess wastewater directly into rivers. In this case, the following significant pollution.
Not everywhere can be connected to a single-family home outside sewer system. In this case, we are forced to ensure that household sewage collected in septic tanks, called szambami, or build a small sewage treatment plants. Sewage runoff, in turn, can be safely discharged into their own property.
tube
Each internal sewage system is performed as gravity. Wastewater generated at home in bathrooms, toilets and kitchens. All connections leading to sanitation in the sewerage system are equipped with traps that effectively prevent the spread of a very pleasant odor. These wires are in turn connected to a common pipe, called divisions.
Most sewage system is made of materials such as PVC and PP, because they are characterized by rigidity and resistance to all substances present in the waste water, acting in an aggressive manner. They are also much lighter than cast iron used previously. Sewer lines are connected socket-, using EPDM gaskets. This ensures durability and tightness of each connection.
Sewers should be properly armed. To this end, the device anti-flooding, sewer drains and traps. Anti-flooding devices are necessary if we are connected to the external network sewer, because they prevent basement flooding due to backflow of sewage.
Sewer drains are used to drain rain water drains, and traps are used to prevent the passage of gases and odors from the sewer to the rooms.
Editing individual sanitary and their connection to the plumbing wall mount installation speeds. Prefabricated walls of this kind is set at the destination, and only then connect the same installation. Once the walls and finish the surface plates are mounted batteries and all sanitary ware.
In each there are plumbing risers, the main pipes that collect wastewater from sanitary facilities, using the approach sewer. Each riser should be of the same diameter throughout. It must be equal to the diameter of the largest connected to the vertical approach. Normally, it is about 100 mm.
The drainage system consists of more laterals (leaky pipes wastewater into the sewage system of the building exterior or holding tank), and gutters.
Author: Commercial Cleaning Chicago & Tiles Restoration Chicago

The housecleaning, gardening should use disposable rubber gloves that protect the delicate skin of your hands before cracks and damage. It should use latex gloves and garden.

Latex gloves protect hands from harmful environmental impacts and have practical applications in the home and garden. Rubber gloves with cotton lining, to prevent sweating hands. They can be used for various household chores. Protect your hands from dirt and chemical agents in the performance of household tasks, gardening. They are very soft and pleasant to the touch, very durable. Protective gloves are very practical when washing dishes, floors, or in contact with other detergents.

They protect hands from exposure to strong cleaning substances, prevent dry skin. Gardening Gloves can have a three-layer structure, which protects and makes them difficult to tear. Their long, distinctive, yellow cuffs to protect arms from scratches and cotton lining prevents sweating hands. They are made of a special blend of rubber and neoprene. By using a special production technologies are mechanically strong and protect your hands from chemicals, household detergents and bleach. They are very flexible, soft, smooth and pleasant to the touch.

Extra virgin on his hands, the fingers provide great feel and grip. Garden gloves are often coated with a special agent that inhibits the growth of bacteria and fungi, and it also lengthens the time of use. Gardening Gloves can be used multiple times. Gloves after use, you need to rinse with warm soapy water and leave to dry in temperatures below 40 degrees C.
Author: Commercial Cleaning Chicago & Maids in Chicago

To clean wooden cutting boards are necessary accessories:

• baking soda,
• lemon,
• Coarse salt
• vinegar,
• hot water,
• kitchen sink.

After using the cutting board, wipe it with a cloth moistened with a small amount of mild detergent or soap.

Make a solution of baking soda and water, just about one teaspoon to a pint of warm water. Then pour it into the spray bottle and spray the board. We thoroughly coat the liquid all cuts and inequality in the instrument, in which could be the remnants of food. Do not forget about spraying or other boards. Instead of a solution of baking soda can be used by a simple hydrogen peroxide, and it is especially recommended for cleaning the boards after handling raw meat or fish.

Rinse the board in warm water, rub her kitchen dish cloth.
Cut the lemon in half and squeeze the juice directly on the board, especially in places cuts, resulting from the use of the knife. Sprinkle with salt.

With the help of the used lemon halves salt scrub the surface of the board, using a circular motion.
Under warm, running water, flush with boards salt and lemon juice.

Dry the board with a paper kitchen towel.
Sprinkle the board with vinegar, then wipe it again with a kitchen towel. Vinegar works disinfectant.
Cooking boards are often used, which is why they need to be cleaned frequently to prevent food poisoning. Cleaning removes them from bacteria, viruses and fungi that are very harmful to humans, especially children. Regular cleaning of cutting boards is the basic hygienic operation, which must be maintained in the apartments, as well as canteens and catering facilities, in restaurants.
Author: Chicago Maids & Chicago Kitchen remodeling